Selaa Kategoriat
Panasonic tuotteet(83)
Laptop Sisäinen asema(91)
USB Ulkoinen(30)
USB Drive Case (Caddy)(13)
Optisen Bay Hard Drive Caddy(33)
Optinen asema Tarvikkeet(23)
SSD, sshd, HDD(16)
Apple Tarvikkeet Varaosat(7)
Aruba wireless access points(24)
Ota yhteyttä
Shenzhen Time In Top Technology Co, Ltd
Osoite:Room 2602, International Science Technology Building,
3007 Shennan Rd., Futian, Shenzhen 518000, China
Puhelin:+86-755-83686434 +86-755-83664959
E-Mail:support@rrdn.netOta nyt
Aruba 655 Indoor Access Points

Aruba 655 Indoor Access Points

  • Brand:Aruba
  • Model:AP-655
  • omprehensive tri-band coverage across 2.4GHz, 5GHz, and 6GHz to deliver up to 7.8Gbps combined peak datarate
  • 4x4 MIMO radios to deliver peak performance and increased capacity using MU-MIMO and OFDMA (uplink and downlink for both)
  • Up to seven 160MHz channels in 6GHz support low-latency, bandwidth-hungry applications like high-definition video and augmented reality/virtual reality applications
  • Unique ultra tri-band filtering enables 5GHz and 6GHz to operate without restrictions or interference
  • High availability with configurable 5 Gbps dual Ethernet ports for hitless failover of ethernet and power
  • Built in GPS receivers and intelligent software enable APs to self-locate and act as reference points for accurate indoor location measurements.

Greater capacity with 6GHz

The 650 Series APs are indoor access points that are fully equipped to support the 6 GHz band for faster performance, wider channels, and minimal interference. Our flagship campus Wi-Fi 6E APs deliver 7.8 Gbps maximum aggregate data rates and 4x4 MU-MIMO.

Maximize channel utilization

Aruba’s patented ultra tri-band filtering allows organizations to take full advantage of 6GHz unlicensed spectrum by dynamically adjusting the available channels to eliminate signal interference and performance degradation.

Highly efficient and secure

Wi-Fi 6E extends the 802.11ax standard to the 6GHz band. All the efficiency and security enhancements including orthogonal frequency-division multiple access (OFDMA), Multi-User MIMO, Enhanced Open, and WPA3 are supported.

IoT ready

Integrated Bluetooth Low Energy (BLE) and Zigbee support make it easier to deploy and manage IoT, including asset tracking, security solutions, and sensors.

Wi-Fi radio specifications
  • AP type: Indoor, tri-radio, 2.4GHz, 5GHz and 6GHz (concurrent) 802.11ax 4x4 MIMO
  • 2.4GHz radio: Four spatial streams Single User (SU) MIMO for up to 1,147Mbps wireless data rate with 4SS HE40 802.11ax client devices (574Mbps for HE20), or multiple 2SS or 1SS MU-MIMO capable 802.11ax devices.
  • 5GHz radio: Four spatial streams Single User (SU) MIMO for up to 2.4Gbps wireless data rate with 4SS HE80 802.11ax client devices, or multiple 2SS or 1SS MU-MIMO capable 802.11ax devices.
  •  6GHz radio: Four spatial streams Single User (SU) MIMO for up to 4.8Gbps wireless data rate with 4SS HE160 802.11ax client devices, or multiple 2SS or 1SS MU-MIMO capable 40 802.11ax devices.
  • Up to 1,024 associated client devices per radio (limited to 2,048 maximum for all three radios combined), and up to 16 BSSIDs per radio (limited to 4 for the 6GHz radio).
  • Supported frequency bands (country-specific restrictions apply):
    • 2.400 to 2.4835GHz ISM
    • 5.150 to 5.250GHz U-NII-1
    • 5.250 to 5.350GHz U-NII-2A
    • 5.470 to 5.725GHz U-NII-2C
    • 5.725 to 5.850GHz U-NII-3/ISM
    • 5.850 to 5.895GHz U-NII-4
    • 5.925 to 6.425GHz U-NII-5
    • 6.425 to 6.525GHz U-NII-6
    • 6.525 to 6.875GHz U-NII-7
    • 6.875 to 7.125GHz U-NII-8
  • Available bands and channels: Dependent on configured regulatory domain (country).
  • Dynamic frequency selection (DFS) optimizes the use of available RF spectrum in the 5 GHz band
  • Supported radio technologies:
    • 802.11b: Direct-sequence spread-spectrum (DSSS)
    • 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
    • 802.11ax: Orthogonal
  • Supported modulation types:
    • 802.11b: BPSK, QPSK, CCK
    • 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM and 256QAM (proprietary extension)
    • 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM (proprietary extension)
    • 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM
  • 802.11n high-throughput (HT) support: HT20/40
  • 802.11ac very high throughput (VHT) support: VHT20/40/80/160(80+80)
  • 802.11ax high efficiency (HE) support: HE20/40/80/160
  • Supported data rates (Mbps):
    • 802.11b: 1, 2, 5.5, 11
    • 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
    • 802.11n: 6.5 to 600 (MCS0 to MCS31, HT20 to HT40), 800 with 256-QAM (proprietary extension)
    • 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160(80+80));VHT80); 2,167 with 1024-QAM (MCS10 and MCS11, proprietary extension)
    • 802.11ax (2.4GHz): 3.6 to 1,147 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE40)
    • 802.11ax (5GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160(80+80))HE80)
    • 802.11ax (6GHz): 3.6 to 4,804 (MCS0 to MCS11, NSS = 1 to 4,HE20 to HE160)
  • 802.11n/ac packet aggregation: A-MPDU, A-MSDU
  • Transmit power: Configurable in increments of 0.5 dBm
  • Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
    • Per radio/band (2.4GHz / 5GHz / 6GHz): +24 dBm (18dBm per chain)
    • Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.
  • Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks
  • Ultra Tri-Band (UTB) enables ultimate flexibility in 5GHz and 6GHz channel selection without performance degradation
  • Maximum ratio combining (MRC) for improved receiver performance
  • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
  • Space-time block coding (STBC) for increased range and improved reception
  • Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
  • Transmit beam-forming (TxBF) for increased signal reliability and range
  • 802.11ax Target Wait Time (TWT) to support low-power client devices
  • 802.11mc Fine Timing Measurement (FTM) for precision distance ranging
Wi-Fi antennas
AP-655: Integrated downtilt omni-directional antennas for 4x4 MIMO with peak antenna gain of 4.8dBi in 2.4GHz, 5.3dBi in 5GHz and 5.4dBi in 6GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 to 40 degrees.
  • Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the combined, average pattern is 3.3dBi in 2.4GHz, 2.9dBi in 5GHz and 4.0dBi in 6GHz.

Other interfaces
  • E0, E1: Two Ethernet wired network ports (RJ-45)
    • Auto-sensing link speed (100/1000/2500/5000BASE-T) and MDI/MDX
    • 2.5Gbps and 5Gbps speeds comply with NBase-T and 802.3bz specifications
    • POE-PD: 48Vdc (nominal) 802.3af/at/bt POE (class 3 or higher)
    • 802.3az Energy Efficient Ethernet (EEE)
    • Link aggregation (LACP) support between both network ports for redundancy and increased capacity
  • DC power interface: 12Vdc (nominal, +/- 5%), accepts 2.1mm/5.5mm center-positive circular plug with 9.5mm length
  • USB 2.0 host interface (Type A connector)
    • Capable of sourcing up to 1A / 5W to an attached device
  • Bluetooth Low Energy (BLE5.0) and Zigbee (802.15.4) radio
    • BLE: up to 6dBm transmit power and -101dBm receive sensitivity (125kbps)
    • Zigbee: up to 6dBm transmit power and -99dBm receive sensitivity (250kbps)
    • Integrated omnidirectional antenna with roughly 30 to 40 degrees downtilt and peak gain of 3.6 dBi
  • GNSS L1 (1575.42 MHz) receiver supporting GPS, Galileo, GLONASS, and BeiDou signal
    • Receive sensitivity: -162dBm (tracking)
    • Integrated omnidirectional antenna with roughly 30 to 40 degrees downtilt and peak gain of 3.1dBi
  •  Advanced IOT Coexistence (AIC) allows concurrent operation of multiple radios in the 2.4GHz band
  • Built-in Trusted Platform Module (TPM) for enhanced security and anti-counterfeiting
  •  Visual indictors (four multi-color LEDs): for System (1x) and Radio (3x) status
  • Reset button: factory reset, LED mode control (normal/off)
  • Serial console interface (proprietary, micro-B USB physical jack)
  • Kensington security slot
  • Automatic thermal shutdown and recovery function
Power sources and power consumption

  • The AP supports direct DC power and Power over Ethernet (POE) on port E0 and/or E1
  • When POE power is supplied to both Ethernet ports, the AP combines power from both sources (SmartPOE feature), using E0 as the primary source and E1 as secondary
  • When both DC and POE power sources are available, DC power takes priority over POE
  • Power sources are sold separately; see the 650 Series Ordering Guide for details
  • The AP supports various power modes depending on the available power source(s) and configuration.
    • With IPM disabled, the AP may apply some static restrictions, see tables below.
    • With IPM enabled, the AP will start up in unrestricted mode but may dynamically apply restrictions depending on the available power budget and actual consumption.
    • Single POE source class 6 (802.3bt) class 5 (802.3bt) class 4 (802.3at) class 3 (802.3af)
      Power budget 51W 40W 25.5W 13.9W
      Power mode Unrestricted Restricted Restricted Not supported
      USB port Enabled Disabled Disabled
      Ethernet Both ports enabled Second port disabled Second port disabled
      MIMO 4x4 2x2 2x2
      Max RF power reduction 0dB 0dB 0dB
      Dual POE source class 5 + class 3+ class 4 + class 4 class 4 + class 3 class 3 + class 3
      Power budget 53.9W 51W 39.4W 27.8W
      Power mode Unrestricted UnRestricted Restricted Restricted
      USB port Enabled Enabled Disabled Disabled
      Ethernet Both ports enabled Both ports enabled Both ports enabled Both ports enabled
      MIMO 4x4 4x4 4x4 2x2
      Max RF power reduction 0dB 0dB 3dB 0dB

      Default POE power modes (IPM disabled)

    • The feature restrictions and order in which these get applied are configurable.
    • When powered by direct DC power, the AP operates without restrictions.
    • Powering the AP from a single 802.3af (class 3 or lower) POE source is not supported, regardless of IPM status.
  • Maximum (worst-case) power consumption (without / with a USB device attached):
    • DC powered: 36.0W/42.5W.
    • POE powered: 40.3W/46.5W.
    • This assumes that up to 5W is supplied to the attached USB device.
  • Maximum (worst-case) power consumption in idle mode: 14.3W/20.2W (DC) or 16.9W/22.7W (POE).
  • Maximum (worst-case) power consumption in deep-sleep mode: 2.4W (DC) or 4.0W (POE).
Mounting details
  • Dimensions/weight (AP-655; unit without mount bracket):
    • 260mm (W) x 260mm (D) x 60mm (H)
    • 1,800g
  • Dimensions/weight (AP-655; shipping):
    • 285mm (W) x 285mm (D) x 95mm (H)
    • 2,300g

Shenzhen Time In Top Technology Co., Ltd


Yhteyshenkilö:Time In Top

Lähetä kysymyksesi suoraan meille näytä koodi kursori syöttöruutuun
( 0 / 3000 )